Samsung Washer Error Codes: What Each Code Means and What to Do
Most Samsung washer codes are about water going in or out: 4C is a fill problem, 5C a drain problem, Ub an unbalanced load and dC a door that isn’t closed. Codes like 3C, 1C and tC point to a part and usually need a technician if they come back.

Rated 4.8 on Google, with 1,200+ reviews online. HomeStars Best of 2026, winner 4 times.
Samsung washers report most problems with a short code on the display. The letters and numbers vary a little between models and model years. Newer displays tend to show a C (4C), older ones an E (4E), and Samsung’s own code lists treat the pairs as the same fault.
Below is what the common codes mean according to Samsung, what you can safely try yourself, and which codes mean it’s time for a repair. If your code isn’t listed, check the owner’s manual for your exact model.
Samsung washer codes at a glance
| Code | What it means | First thing to try |
|---|---|---|
| 4C, 4E | Water supply problem: the washer isn’t filling properly | Open the taps fully, check the hoses for kinks, clean the mesh filters where the hoses connect |
| 5C, 5E | Drain problem | Clean the drain pump filter and check the drain hose for kinks or blockages |
| Ub, UE | Unbalanced load | Spread the load evenly; add two or three towels to a single heavy item |
| dC, dE | Door problem | Close the door fully and check nothing is caught in it |
| LE, LC | Low water level detected | Check the drain hose position and look for leaks |
| 3C, 3E | Motor issue | Power off at the wall for 1 minute, then start a new cycle |
| 1C, 1E | Water level sensor issue | Power off for 1 minute and restart |
| tC, tE | Temperature sensor error | Power off for 1 minute and restart |
| HE, HC | Water temperature or heating issue | Check the inlet hose is on the cold tap where your manual says so |
| Sud | Too much foam | Use HE detergent at the right dose; let the washer clear it |
| 8C | Vibration (MEMS) sensor issue | Turn off and restart the cycle |
| 9C | Low voltage | Plug the washer straight into the wall, not an extension cord |
Samsung’s reset for most part-related codes is the same: switch the washer off at the wall for one minute, switch it back on and start a new cycle. If the same code comes back, the washer needs a technician.
4C and 4E: the washer isn’t filling
Samsung’s checks for a fill code are to open the taps fully, make sure the supply hoses aren’t kinked or clogged, and clean the small mesh filters where the hoses connect to the back of the washer. Those filters collect grit over time and slow the fill until the washer gives up. In winter, a hose or tap in a cold garage or basement can also freeze. If the code keeps returning with good water pressure, the inlet valve is the usual failed part. Our Samsung 4C guide goes through it step by step.

5C and 5E: the washer won’t drain
A drain code means water is still in the drum when the washer expected it to be gone. Most Samsung front-loaders have a drain pump filter behind a small panel at the bottom front, with a short emergency drain hose next to it. Put towels and a shallow tray down first, drain the water through the small hose, then unscrew the filter and clear out coins, hair ties and lint. Check that the drain hose isn’t kinked behind the washer. If the pump hums but doesn’t move water with a clean filter, the pump itself may have failed.

Ub and UE: an unbalanced load
This isn’t a fault. The washer has sensed the load bunched to one side and won’t spin fast until it’s balanced. A single bath mat, a pillow or one pair of jeans is the classic cause. Spread the load out, add a couple of towels to a single heavy item, and make sure the washer sits level on a solid floor. If Ub shows up on normal, mixed loads, the shock absorbers or the suspension may be worn. See our Samsung Ub guide for the details.
Rather have a technician look at it?
You get an upfront price before any work starts, and the service call is waived when you go ahead with the repair. Same-day appointments across Toronto and the GTA when a technician is available.
dC and dE: the door
The washer won’t start, or stops, if it can’t confirm the door is closed and locked. Close it firmly and check that no clothing is caught in the door seal. If the code persists with the door clearly shut, the door lock or the latch is the likely part.
Codes that point to a part
3C (motor), 1C (water level sensor), tC (temperature sensor), 8C (vibration sensor) and the heating codes all report a component that isn’t behaving as expected. A power reset is worth one try. If the code comes back, the part needs testing with a meter, which is a job for a technician.
Sud: too much foam
Too much detergent, or regular detergent in a high-efficiency washer, makes so much foam that the washer pauses to let it settle. Use HE detergent at the dose on the bottle, less for small loads or soft water. If Sud appears often even with the right detergent, the drain pump or filter may be partly blocked.
When to call a technician
Book a repair if a code returns after the checks above, if the washer won’t drain with a clean filter, if water leaks from underneath, or if you see a motor, sensor or heater code. Tell us the code and the model number when you book; it helps the technician bring the right part. You’ll get a written price before any work starts. See Samsung appliance repair or washer repair in Toronto.
Sources
- Samsung Support: What do the codes on my washing machine mean?
Sources checked in November 2026. Steps and codes vary by model, so check your owner’s manual too.
Frequently Asked Questions
How do I reset a Samsung washer error code?
For most codes, switch the washer off at the wall for one minute, switch it back on and start a new cycle. If the same code returns, the cause needs fixing first.
What does 4C mean on a Samsung washer?
A water supply problem: the washer isn’t filling properly. Check that the taps are fully open, the hoses aren’t kinked and the mesh inlet filters are clean.
Is 4C the same as 4E?
Yes. Older Samsung displays tend to show E codes and newer ones C codes, and Samsung lists the pairs as the same fault.
Why does my Samsung washer keep showing Ub?
The load is bunched to one side. Spread it out and add towels to single heavy items. If it happens on normal loads, the suspension or shock absorbers may be worn.
Is it worth repairing a Samsung washer with a 3C code?
Often, yes. 3C can be the motor, its wiring or the control, and the right repair depends on which. A technician tests it and gives you a written price first.
*Same-day service is offered whenever possible and depends on technician availability, parts, and your location within the GTA.